We rested this summer in the Carpathians (Ukraine) .... Wonderful places, beautiful nature, aromas of herbs and forests! And these aromas I wanted to pick up with me home - I bought a wonderful sachet pad. This roller exudes just stunning fragrance! And everything would be fine, but this cushion in the interior of my bedroom did not fit.
I had to sew a new pillowcase. The style chose vintage with Shebbi elements.
So, here is such a pillow we have
Materials for work:
- Cotton fabric - in my case 2 types
- Sewing cotton width 4 cm.
- Ribbon satin width 0.7 mm
- Sewing threads
From the tools we will need:
- meter Portnovsky
- Pins Portnovsky
To begin with, we take measurements: we are interested in the length of the roller and width
Draw a pattern. I decided to complicate the task, and to melt the pattern on the combinations of 2 types of fabrics and cotton sewing.
To figure out what and on what pieces to cut fabrics, you must first draw these moments on paper. I chose such parameters where dark cotton goes around the edges, white is a lace, and the SERSE - a fabric gray with a "rose-cell rosets"
The width indicated. Do not forget that these are the sizes in the finished form - and so that these parts are between themselves - it is necessary to add each of them to the seams. To do this, the pattern is cut on the resulting strips, and each band is added on each side of 0.7-10 mm. Like this
Cut the stripes from the fabrics that are already cooked. Do not forget about lace-sewing. Become - we get such a rectangle
We have seams. We put half on the smaller side, face inside. We fasten the needles along the edge so that when sewing the side is not spread. Still. Important moment! When applying the middle seam - leaving from each edge an unimposed hole equal to 0.8 cm., At a distance of 1 cm. From the edge.
We turn out the edges of the resulting "sleeves" to the wrong one for 1 cm. We flash the zigzag lines. Turn out the product.
Next, we take the satin tape length (as for whom you need)))) I took 50 cm. In order for the gates to be soft and falling. One thing, we attach the pin and stretch into the hole, which we left unimpressed (it was already inside the pillowcase) Now, wear pillowcase on the pillow and tighten the tapes very tight. Tie bows.
It turned out a pad such as not to know already. And since I used the materials only natural, I can safely put it in bed - the dream will be strong and healthy! What and wish you!
Pillow-roller, with your own hands stitched from inexpensive and affordable materials, can serve as not only element of the decor. Orthopedic varieties are useful for a good sleep, a small roller can be taken with you on the road with a long trip on the bus, train or car. Make a pillow of the desired size and form is easy.
The focus should be given to packing. If the pillow-roller is decorative, then the density and the texture of the valid value does not have. Such a product can be filled with even a rag, recycling old T-shirts, sweaters, etc.
For orthopedic or bedroom pillow in the shape of a roller filler pick up the density:
- Buckwheat husk - environmentally friendly, but tight material, the pillow will be tough;
- Hollofiber - synthetic, soft and comfortable material;
- Porolon - depending on the density of the sheet material, you can make a pillow of the desired stiffness, and it is better to fill the decorative products with cut off;
- Pooh and feather are poorly suitable for the manufacture of roller, since they have too loose structure, but for a soft pillow you can use them.
In addition to filler, you need the following materials and tools:
- Fabric for the base of the pillow (durable, dense, without decor);
- material for the case (decorative varieties);
- Clasp fastener (lightning, velcro, buttons, etc.);
- Treads sewing, respectively, tissue density;
- machine sewing machine;
- Portnovo scissors;
- Measuring tape or long line, chalk or pencil.
How to choose the shape and sizes of the pillow?
Making cushions for the sofa can be many different ways. The choice of form depends on the purpose of the product:
- decorative fill in the covers of an unusual shape, contrasting the color sofa or pick up a strict trim in the tone, decorated with appliqués, cords, ruffles and bulbs, etc.;
- Sleeping (for bed) are not accustomed so clean, it is enough to make a natural cloth cover, which is easy to remove for washing;
- Orthopedic may have a curved shape to hold their heads during sleep in the desired position, you can make a roller for your back when working in an office chair, etc.
Before developing the design, you need to determine what the pillow will be sewn, and choose its shape and convenient size (length and diameter). In accordance with these requirements, there is a sketch of external registration of the cover and build patterns for the base and the removable part. With rod pillowcases, it is advisable to make a small allowance so that it was easier to put on the basis.
How to sew a pillow-roller?
A straight pillow with a roller does not require a complex cut. But the pattern for her still have to do (if you need a few identical products, the template will simply need).
The pattern of a simple roller builds so:
- determine the desired length and thickness (diameter) of the product;
- on a sheet of paper drawn 1 part of the side part - a rectangle with a long side equal to the length of the finished roller, and a short, equal length of the circle of the diameter that will have a product;
- For the end parts, the circle of the selected diameter is drawn (from the tissue you need to draw 2 parts such).
This is an option to make a case for a decorative sofa dummy. The basis is sewn by pattern, common to all rollers: direct cylinder with filler.
The easiest case of the pillow of the "Candy" cushion is sewn so:
- measured the length of the base of the pillow and its diameter;
- There are a rectangle with a short side equal to the length of the roller circumference, and to the length of the base, it is added to its thickness and the desired length of the "phantha tails", multiplied by 2;
- The rectangle is cut, processed the edges, decorated and stepping the side of the cylinder (it can be done on the clasp, but more often in the candy the base is inserted through open ends);
- For the formation of "tails", the extra part of the material on the ends is tightened with decorative ribbons or cords.
The embodiment of the edges of the candy - Kulisk, sewn with the inside of the cover before its assembly. The distance from the edge of each end of the base to the Kuliska is ½ thickness (pillow diameter). Cords or rubber bands insert into the stem.
Variety of pillowcase candy. Circling a rectangle is needed to size the base of the pillow (length and diameter). To close the ends, it is added to the thickness of the product to be added to its thickness with a small switch (4-7 cm) for free felting and the scene of the edge.
The assembly is made like this:
- cut out the pattern;
- Move the edges of the short sides of the rectangle (ends) so that the cord can be tested;
- decorate the surface, adjusting applications, ruffles, etc.;
- stitch the sidewall of the cylinder;
- They put on the pillowcase on the basis through the open ends and tighten the edges by the extension with cords.
Roller on zipper
It is also easy to sew a roller on the lightning. A simple version of such pillowcases is lined in templates for the base: 1 Detail of the sidewall (large rectangle) and 2 circles for the end parts.
If the product should be complex, for example, from 2-3 parts of different colors, the pattern of the sidewalls split along or across the strips for each shade, not forgetting to add an allowance to the seams (1-1.2 cm). Cutting decor (applique) need to be touched on the pillowcase before it is assembling.
In a simple embodiment, the assembly is carried out like this:
- on the long sides of the rectangle are dodged with lightning;
- connecting it parts, turn the cylinder inside out;
- On the end sides, round parts, combining the edges of the fabric facial sides to each other;
- If necessary, you can insert a decor from the material strip, folded in half: it is combined with sections of the circle and cylinder end;
- The sour cream product is pasted around the circumference, fixing the ends of the zipper ribbons;
- Estably and turned on the face, put inside the base of the pillow.
How to make a pillow for neck
The cushion-roller under the neck must be curved. For it, a more complex pattern is built, determining the size of the inner diameter of the arc in the size of the neck. The thickness (diameter) must be determined by the convenient position of the head in the support on the roller. The width of the arcuate pattern depends on the pillow diameter: size 1 of the part is ½ of the circumference length.
You need to paint separately the upper and lower parts of the sidewall (one template). The end parts can be closed with round parts, like a straight roller, or simply sew the edges of the fabric on the sidewall elements. For convenience, in the latter case, the ending edges of the sidewall details curl.
Both the base and the pillowcase in this case are sewn by one patterns. Lightning or other clasp put on the outer side of the arc so that the convex details were not pressed on the neck and the pillowcase was easier to remove or put on. Figure the basis better by scattering material: buckwheat luzga, cut back foam, etc. It is convenient to use Hollofiber.
Sheet foam, rolled into the cylinder, is undesirable: when it is bent in the form of the pillow, uncomfortable folds may occur. To sew an orthopedic pillow with your own hands, it is best to buy a thick sheet (or glue a few thin plates) and cut out the detail on the pillowcase pattern from it.
How to make a roller in a crib for a child?
The roller in the crib sew the same principles as for adults (on the pattern of a direct cylinder). The main difference is the dimensions:
- The length of the roller must accurately match the inner width of the bed, if it is used as a pillow (across);
- The thickness is selected depending on the age and growth of the child: it is best to make a workpiece from any material (minimize into a roll) and offer to lie on it, and then measure the convenient option.
For the basics and external shell, use traditional natural materials: a dense satin, a special tissue tissue (for the base), as well as linen and cotton fabrics for pillowcase.
I will tell you how to choose a decorative pillow on the sofa. After all, in contrast to the traditional pillow for sleep, the sofa decor is needed not only for a comfortable stay, but also to create a comfortable atmosphere of comfort and warmth in the house, how to make patterns and sew with your own hands.
Appointment of decorative pillows
There are several reasons why the pillow on the sofa must necessarily be:
- Clearly and correctly selected shape, color and size of the sofa decor helps to emphasize the general style and design of the room;
- The original cushion decor emphasizes the tastes and individuality of the host of the house;
- Sofa pillows create an amazing atmosphere of home comfort and heat;
- Sofa decor can adjust some lack of interior.
Decorative pillows have long been the usual element of any interior.
There are no negative points in the use of a soft product, provided that the form, color and size are chosen correctly.
Types of sofa pillows
Amazes the variety of sofa pillows:
Turkish - oblong in shape, decorated with brushes or by volanses, are distinguished by the characteristic oriental ornament of the tissue.
Rollers - small pads - Dumas, the main purpose of which is to serve as a soft stand during daytime sleep on the sofa.
I wonder the pillows rollers in the interior
Quilted - square, oval or rectangular pillows, the main difference of which consists in the sealed surface of the cover.
Sectional - bulk versions consisting of several parts connected by insertion.
Dumka is a classic version of a small pillow.
Bright pillow Dumka
Oxford - option with a border without packing around the perimeter. At a distance of several centimeters from the edge, an additional line creates the perimeter, creating a kaym.
Oxford pillow Patchwork Pillows
Material and content
General requirements for filler:
- health safety;
- simple care;
- property preserve form;
Most often, the product is filled with syntheps. This is affordable, lightweight, well preserving material.
Also, a good filling option will be holofiber - practical and durable synthetic material. Hollofiber produces their polyester fibers, they have a great shape, very little weigh. Models with a holofiber filler, can be cleaned at home.
Pillows from Singrytegone Soft and do not cause allergies
- For those who prefer natural materials, choose down or feather.
- Natural filler is not recommended for those who are inclined to the development of allergic reactions.
- The main thing that the pillowcase was not only beautiful, but also durable, and comfortable in washing, since the sofa decor is often erased.
Pillowcase for pillow
How to choose correctly
Picking up, follow the following principles:
- Moderation. If the room already has volumetric, attracting attention to decor objects (for example, bright panel or picture) does not need to fill the sofa with a large number of pillows.
- The ratio of furniture and sizes. No need to fill the entire surface of a small sofa with huge models. A good solution: for a massive sofa, choose two or three bulk options, and for a small sofa are somewhat small.
- Combination in form. For low models of the sofa (sofa, ottoman), there will be rectangular, small models. To emphasize the refinement of classic models of sofas with high backs capable square or round options with brushes.
- Contrast in color. Decorative soft model color emphasizes style and general atmosphere. Do not choose decorative elements on the sofa repeating color and upholstery pattern of furniture. A good option: the color of the product is brighter, juicy the total range of rooms, with patterns combined by style and design with other elements.
In addition to practical functions, sofa pillows can also carry decorative
How to sew alone
Here is such an interesting option, I specified my own hands from the shirt (by the way, this is a good way to recycle old, unnecessary things).
- Shirt turn inside out.
- The product attach to the shirt and circle along the contour. The secret is that the plank with buttons should be located exactly in the middle of the product.
- With letters on the seams cut the circled billet.
- Stop the workpiece around the perimeter.
- Remove the Czech, ignite, try on the product, button buttons.
Decorative shirt pillow
New Sofa Decor Ready! You can use the old sweater for the manufacture of a soft product.
Ideas in the interior
The main rule of the choice of designer decor is a combination with the stylistic room.
So for the classic style, the variants of the right geometric forms from dense-valve tissues (tapestry, velvet) are ideally suited. Oriental style will emphasize the products of bright colors, with an ornamental pattern, decorated with embroidery, brushes.
Decorative Cushion Classic Style
For those who prefer modern style minimalism or high-tech will appreciate the models in natural leather covers without any additional decor.
Country design will emphasize the products in Czechs from burlap or jeans.
So that the interior was not boring and faceless, remember the main mistakes, and never take them:
- Do not pick a sofa decor case into the upholstery of upholstered furniture;
- Do not go products from the upholstery fabric;
- boring and trite look like products from fabric repeating on the curtains;
- The sofa decor is poor and boring, if all the half of the same color.
Properly selected sofa pillow - the fastest and easiest way to bring the individuality to the interior, to create a unique atmosphere of heat and comfort.
A source: https://bezkovrov.com/spalnja/dekorativnay-podushka.html
How to sew a pillow roller with your own hands? Patterns for different options. Pillow-roller with your own hands - the indispensable attribute of comfort and coziness cylindrical pillow roller
The home interior consists of a variety of details that create cozy heat in the house. One of these interior items is a decorative sofa pillow in the form of a roller.
Such pillows together with puffs and carpets came to us from Eastern culture. There they played the role of armrests on couches, wood sofas.
Horse hair, straw or dry fern leaves served by fillers for them.
But the fluff and feathers for filling such rollers did not use, because The armrests were supposed to be quite elastic to maintain their shape and not to see the sweat of the body.
Nowadays, the sofa armrests turned into a fashionable accessory - a cushion-cushion-roller on which you can lie down or rely on while watching TV or reading a book.
If you like Hend Maid, then such a pillow-roller can be easily seeded with their own hands, using the remnants of various flavors of dense tissue.
The sizes of the pillow can be absolutely any, they are determined based on your preferences or sofa size.
The ends of the pillow can be arranged with flowers from textiles, decorative brushes, pleated, bows, ribbons, rushes, appliqué or decorative embroidery.
On covers for such pillows often make comfortable fasteners on velcro, butt or zipper. Then they are very convenient to remove and wash as pollution.
As filler uses syntheps, cotton wools, holofiber, foam rubber and other modern materials. You can also use ready-made pillow inserts. They can be easily purchased in textile stores, where there are inserts of different sizes.
It will only remain sewing the cover of the desired size, insert the insert and the pillow is ready.
Such a stylish subject of the interior can also sew a beginner needlewoman from any tissue residues. Today we consider how to sew a pillow-roller with your own hands on a simple pattern.
Pillow with edging from cord
To sew such a simple, but a very comfortable roller pillow, we need to stock up minimum materials and a pair of hours of free time.
To work, you will need:
- Dense fabric (velveteen, jacquard);
- Threads in tone tissue;
- Portnovo meter;
- Galla line;
- Simple pencil;
- Sewing machine.
Instructions for sewing
Let's start with the cutting of the main part of the cover. With the help of a triangle ruler, we cut a smooth rectangle from the fabric. In which the longitudinal parties will be shorter than the parties that are sewn to the end round parts. The dimensions of the rectangle are made in their measurements.
Now Crow edging for round side parts of the pillow. The width of both cuttings should be wider than the main web for 4-6 cm. The width of the sheets should be 8 cm.
Patterns round ends are placed using any round item as a stencil (plate, cover from pan, bucket, etc.). Cut two identical details.
Now proceed to the tailoring of the roller and the sewing of lightning. We fold a large pattern face inside, we spawn the side seams with pins.
We spend the side seam by 1.5-2 cm from the edge.
In the "Couple" mode, we smoothed the resulting seam by turning the edges in different directions.
Now we apply zipper, we sweat the pins of one side, as shown in the photo.
Shot seams are stitching on the sewing machine. Then we pins the other side of the zipper by pins, add the second edge of the lightning to the base. In order to protect the edges of the seams from the spreading, coach them with a jigsag. The transverse short suture is fixed by the edge of the zipper, cut off the unnecessary part of the snake.
Special tool break the side seam. As a result, it turns out neatly sewn hidden lightning.
Now proceed with decorative edging. We start inside the short edge of the patterns 1-1.5 cm wide. Then folding the workpiece in half, weching it, as shown in the photo.
On the root line, we lay the cord, longitudinously fold the part in half. We challenge pins so that the cloth makes the cord tightly.
- We pave the seam at the mark, as close as possible to the cord, securing it securing it inside the edge.
Excess fabric cutting off. Through the edge of the free edge, we make small frequent cuts to make the item without having a round shape. We make two details.
Now we take one detail of the round end, add one edge edge to the edge of the circle. Now the pins gently take all the edging in a circle, cutting up too much.
After that, in the background, we admonish the edging with the cord to the side part. Similarly, we make the second item.
The main billet is turned inside out. We apply the end part to the face to face, mock the seam connection with pins.
- We pave a machine seam along the edge at a distance of 1.5 cm.
Open zipper, turn the pillow on the front side. Here is our pillow-roller and ready, it remains to put the filler and close the zipper.
Color Pillow on Buttons
Such a pillow will be added to the interior of bright colors and a little romance. For its tailoring, the remains of any color tissue are suitable. Total will need 4 motley colors.
To work, you will need:
- 4 pieces of bright dense fabric;
- Cylindrical liner (length 35 cm, diameter 15 cm);
- 3 decorative buttons in the form of hearts;
- Tools for sewing (scissors, pins, threads, needles, machine).
Instructions for sewing
We choose 3 colors of the fabrics, which will go to the main part, and leave the fourth segment to cut round ends. We sew among themselves three rectangular loskut in the length of the finished roller. From the fourth loskutka, we cut two circles with a diameter of 15 cm plus 2 cm on the allowance.
Seams are wearing in different directions, coach the edges by Zigzag so that they do not strengthen. The billet should be 35 cm in length in length plus 3 cm on the seams and the width of equal length of the circumference plus 2.5 cm on the seams. Both edges of the main canvases are sewn, we grasp a width of 2 cm.
On the one hand we will make the loops, with another sequence of curtain buttons.
Along one edge from the front side, we sew three buttons at the same distance from each other. For the gap, retreat from the edge of 4-5 cm.
- From the opposite edge, opposite each button, we tighten 3 loops, make cuts inside them.
- Buttoning buttons, turn the cylindrical blank inside out, take the pins round parts of the end parts, attaching them to the front side inside.
Now adding parts to each other, cut off everything too much. All seams are carefully trimmed.
Spread the product is obvious, we put inside the cylindrical liner, fasten the seam. Here is a pretty cushion cushion, stitched with your own hands on a simple pattern.
Hands with a stitched roller pillow can be accommodated for the decor of the bedroom, living room or country gazebo. And if you sew a case of waterproof tissue, then it can be placed on a chaise lounge near the pool or take with you to the beach.
For tailoring, it is better to use a dense fabric that will be sufficiently resistant to abrasion, but not rude to the touch. Color range can coincide or contrast with overall textile coloring in the room.
POST Views: 114
The art of a real holiday, comparable to the immersion in Blessed Nirvana, came to us, overcoming time and space, modifying and transforming, from the countries of the East. It was on this mysterious and blessed land that the first fluffy carpets, sofa pillows and soft puffs were created.
Over time, in the art of creating these products, the eastern masters reached the present perfection. Why not borrow their experience, and not create a product for comfort and comfort, taking advantage of the advice of experienced artisans.
One of the most simple and useful products for the interior and recreation is the original pillow in the form of a roller.
Pillow roller with their own hands is a completely feasible project, for the implementation of which even the most inexperienced needlew maker does not need no more couple of hours.
Yes, a cushion roller with your own hands is created in a matter of hours. It is not much at all, even for our rich rhythm of life. At the same time, all work is performed in full compliance with the technological rules characteristic of this eastern product.
Why do you need a pillow-roller?
Pillow roller with their own hands is a great opportunity to quickly and exercise to become the owner of a stylish accessory and just a useful thing.
Earlier, rollers - before the appearance of upholstered furniture, was used as armrests attached to rigid wooden couches and sofas. These elongated pillows stuffed usual for those times. horse hair;. dry fern; straw.
But the feather and the fluff were not at all suitable for packing such pillows, since the soft stuff did not allow it possible during the secular conversation, and at the same time elegantly, rely on the roller.
Of course, Fraki and Tournights have long moved into the past, but this does not mean that the pillow roller do it yourself - the case is no way and irrelevant.
On the contrary, these original products from the "sofa team" are still claimed, relevant and perfectly fit into most modern interiors.
Pillow roller with their own hands, made in the form of a cylinder, is made of one piece of fabric or from several bands, harmoniously combined with each other. For packing, you can use any suitable filler.
A special fantasy is shown when the ends - a cushion of a roller with your own hands, this is a great opportunity to show your creative abilities. For example, for the design of the ends often use:. folds;. Edging;.
. Decorative buttons;
What instruments and materials do you need?
Pillow roller with their own hands will require the following materials and tools:. Extra density fabric - it can be tapestry, boston, coarse calico or microwave;
Pillow in the form of a roller, packed by octo, feathers or synthetic packing;. Decorative cord - for edging;. Large buttons, tinted with cloth, as well as brushes and outlets - for decoration; Buttons and lightning;. chalk and ruler;.
Santimeter and scissors;. Sewing machine;. Needles, threads and pins with looping.
First of all, the future location of the pillow is measuring - this will avoid unforeseen inconsistencies in the size of the product and the bed.
The ready-made cylindrical cushion is stitched or purchased - should exceed the volume of the roller by approximately 10%.
The manufacture of the case, on the contrary, is made at exactly the calculated dimensions - then the pillow roller will acquire a clear outline and the required elasticity.
Options for sewing
1. Perfect the size on the wrong side, add two centimeters from all sides - to the allowance. Strip the desired fragment. Watch that the lower and top side of the cut slices are equal to the length of the end of the end, and the side edges - the length of the roller.
Scholov Fabric on the side of the sides of the face inside, retreat 2 cm from the untreated edges, from the ends - 15 cm. Stitching on the long side. We sew zipper, sew buttons or buttons - for fastening the cover.
On the remaining tissue, we draw two circles - ends. We add to the circles on the seams - 2 cm. Cut and cut the allowances - so that the circles do not wrinkle. In the perimeter, sew edging cord. Next, we perform an incision of end edges of the case. The step and depth of the cuts - 1.5 cm. SCOLs face the front side of the ends and edging, pass.
Afterverting the pillowcase, check the quality of the seams. If there are flaws - correct. The ends should look flawless. Everything, the case can be worn - the pillow roller is ready!
2. In accordance with the length of the cylinder and the radius of the ends, we calculate the dimensions of the "tailings" that will be tied to the end of the pillow. Similar to the first option, we make the pattern - you need a band of fabric equal to the side edges of the length of the pillow, and along the lower and upper sides - the end circle.
Upon all edges, we add to the seams - 3 cm. Next, we rock and spend the blank from the wrong side - along the long side. Having turned out the end side by half a centimeter, we shoot. Then we sew the tails, we put the roller into the case, tie the ends - the pillow roller is ready for your own hands.
3. Having placing and handling, sew the case, similar to the first option. From two ends, we carry out the edging by cutting the cord so that on the ends it was one junction. Crow two bands of the fabric. The width of the addition billets should be equal to the end radius, length - the length of the end of the end. On each side of the cut should be left on the seams - 1, 5 cm.
Scholov and sewing short ends, one long side of the workpiece adds along the edging to the end. Fitting and having twisted the free edge, we draw a cord or braid into the resulting stem. Next, repeat all operations on the second end of the roller.
Having invested the pillow to the case, tighten the cords, tie them, and then stitching - for extra strength. Cut the ends of the cords. An adjacent hole formed in the middle of the end is closed by a button, a tassel or a socket.
There are many different ways associated with the manufacture of pillow-rollers quickly and just do it yourself. It creates the necessary comfort for the neck and head, and also serves as a good interior decoration. On such a pillow, it is convenient to read the book, watch TV or simply dorm.
Knit crochet pillow-roller with your own hands in step by step MK
- Crochet can be associated very interesting covers for pillows under the neck.
- The size of such a product is 45 cm in length and 14 cm in diameter.
A source: https://www.kalinark.ru/upholstered-furniture/kak-sshit-podushku-valik-svoimi-rukami-vykroiki-domya-raznyh-variantov/
How to properly sew a pillow from the foam roller. Pillows Valleys: Decorative and Medical Properties
Spine - Support of the entire body. The back is constantly in tension, even when a person sits or lies. Any problems with this part of the body are immediately reflected in the state of health and human ability. Incorrect posture is also the cause of many diseases. To remove the load from the back in a dream, the mattress and pillow are correctly chosen.
Advantages of roller pillows
The orthopedic roller for the back is necessary to maintain the spine at a convenient position. A specially designed shape in the form of a roller, or with a flat back allow the lower back to acquire a natural bend. Due to its rigidity, the load on the spine comes down to a minimum.
- removal of the load from the spine during the seating;
- maintaining the loin in natural form;
- restoration of muscle tone;
- Prevention of osteochondrosis;
- treatment of scoliosis;
- Reducing the volume of movements.
Orthopedic seating pads can be used all the time. In the first days it is better to be limited to several hours for the adaptation of the body. The first week a person can complain about deterioration, but after adaptation, well-being will only improve.
The seating roller is especially relevant for drivers who spend entire days in the voltage.
Depending on the filler, the pillow can have a memory effect. The material is adjusted for the individual characteristics of the body.
Pillows rollers can be put under the neck during sleep. Ordinary feathery pillows, especially the wrong height, contribute to the development of spine diseases, can additionally cause allergic reactions.
As a result of the wrong choice of the pillow, a person feels:
- Painting pain in the neck area.
Because of the wrong position of the neck during sleep, the upper spine does not rest. Osteochondrosis and migraine can develop.
The orthopedic pillow will ensure the correct position of the neck, as a result:
- Straighten the chest spine.
- The head is not bent.
- The chin is in the natural position.
By laying a roller under the lower back, you can achieve the unloading of the muscles of the lower back.
What to choose a filler?
There are several options for filling orthopedic products for the back. Requirements for filler:
Frequently used fillers:
- Polyurethane foam.
- Buckwheat husk.
Memory function allows the pillow to memorize the body shape. With each use, rest will become more comfortable and full. After a hard working day, a cushion with a cooling effect is perfect.
The most affordable filler is buckwheat husk. The material is inexpensive, it is natural and high-quality. Such a pillow serves more than one year.
How to choose a height?
Pillow roller can be used in different ways:
- put on the neck;
- put up under the lower back;
- used to sleep on the side;
- Apply instead of a pillow.
Choosing a pillow-roller you need to focus on your own feelings. Making even the most accurate calculation of the height, the pillow may not be suitable due to the high weight of a person, due to an uncomfortable mattress and other factors. The feature of orthopedic devices is imperceptibility when used, during rest they should not be felt.
To measure the height of the sleeping roller, you need to measure the distance from the neck to the shoulder, the 1-2 centimeter is added to this magnitude as compensation from the molding of the mattress shoulder. If the shoulders are wide, then the high roller will be required, which are found not so often.
When choosing a roller, such nuances are marked:
- The base of the roller must be tough;
- The average height of the 8-10 cm roller is suitable for almost everyone;
- If the matress is soft, the roller should be higher;
- Ifrson is advantageous on the stomach, then the roller is not used.
Pillow-roller do it yourself
To make a roller with your own hands, it is important not only to enjoy minimal sewing skills and the necessary materials, as well as choose the right filler. In order for the pillow to retain the form and was comfortable, buckwheat husk is used. Porolon for orthopedic products does not fit.
Pillow-roller - simple and spectacular decoration for your home
Many interior items came to us from the East, for example, soft carpets, comfortable puffs, sofas and pillows. The pillow-roller also appeared first in the east. Previously, soft rollers performed the functions of armrests on wooden sofas and couches. They were stuffed with horse hair, dry fern or straw.
Feather and Pooh did not use as a filler for such armrests, because the rollers of them were not enough for themselves, it was impossible to rely on them during rest, reading or conversation. Today, the sofa rollers are also very fashionable and practical objects of the situation.
Pillow-roller has a cylindrical shape. It can be sewed from a solid piece of fabric or from different stripes. The size of the product depends on the sofa size and your taste.
The roller ends can be separated by decorative elements, such as folds, assemblies, pleated, etc. Attractive looks of this type of patchwork, when the pillowcase is performed from multi-colored flavors of the fabric.
In addition, the roller will look good lace or hand embroidery.
On the pillowcases for such pillows most often make a zipper, because it greatly simplifies the use of roller. If necessary, this pillowcase can be easily removed for washing. Today, sofa pillows are filled with synthetic materials, such as foam or hollofiber.
The pillow-roller is not difficult to sew at home. Make this object of the interior may even begin the needlewoman. Today we will tell you how to sew a decorative pillowcase for a roller pillow with a decorative edging on the ends. You can make such a pillowcase in just two hours.
Tools and materials:
- dense fabric - ,;
- Portnovo meter;
- simple pencil;
- Galla line;
- sewing machine.
1. Pattern of the main part of the pillowcase
Cut a rectangle. To carve a smooth rectangle, it is best to apply a carbon ruler. The longitudinal sides of the rectangle will be shorter than the parties that are sewn to the end round parts.
2. Pattern of edging for lateral parts
Edging for the side parts must be 4-6 cm wider than the main part of the roller. The width of the garbage is about 8 cm.
3. Pattern of the end parts
The end part can be carved by outrubing any rounded subject, for example, a bucket.
Gently cut the resulting circle.
All items should look like this as in this photo.
5. Pulling the base of the roller
In the side line of the main part of the roller will be sewn lightning. But we will now show you the original way of stitching lightning. So, turn over the main part of the roller and barrier on the side line.
6. Stitching the basis of the part
Stretch the side seam at a distance of about 1.5 cm from the edge.
7. Side seam service
Find the side seam iron on the function "Couple" or through wet gauze. Sunshine seam in different directions.
8. Sewing lightning
- Print the lightning pins to one side of the side seam.
- Start a typewriter on one side.
- Then pinched the lightning pins to the other side of the side seam, as shown in the photo.
Take a second edge of lightning to the base. Change the edges of the seam Zigzag.
Throw on the typewriter seam across lightning. This seam will fix the edge of the zipper.
- Cut unnecessary "tailings" of lightning.
- Then the special tool will restrain the side seam.
- You have to get such a beautiful zipper.
- 8. Making decorative edging
- Squeeze one end of the workpiece inward at a distance of 1 cm.
- Fold the workpiece in half and start it, as shown in the photo.
- Insert the cord workpiece inside.
- Space the blank by pins, so that the fabric tightly wrapped the cord.
- Stretch the seams very close to the cord.
- Cut the surplus of the fabric.
- Make small cuts so that the blank is easy to turn around in a circle.
- Take one end of the decorative edging to a round side part.
Pins stick all edging in a circle. Cut the surplus of the fabric.
- Squeeze the edge to the mechanical part of the typewriter.
- Treat the second end part in the same way.
- Remove the main part of the roller on the wrong one and attach the end part to it, as shown in the picture.
- Print the end parts to the main part of the pins.
- Stop out the typewriter on the edge at a distance of 1.5 cm.
- Open the zipper and remove the product on the front side.
- Here is your wonderful roller pillow!
- Expensive needlewomen, go to our page in
Perhaps we all need to learn from the Japanese the rules of good sleep. They sleep on the back, on a hard special mattress, and under the head lay a log in the pillowcase.
In their opinion, only such a body position during sleep provides a full-fledged rest and relaxation throughout the body.
Our mentality is fundamentally different from the eastern vision of the world, but no one bothers a little to adopt their rest way: you can sleep on a more rigid bed, and instead of a log may well be used Pillow-roller .
It has long been proven that sleeping in large and high pillows is harmful. And rollers, on the contrary, are suitable for this purpose for all 100%. They are low, sufficiently solid and are placed directly under the neck, thus allowing the spine to be in an even position.
Before we start listening all the advantages of such pillows, let's see what kind of rollers exist:
- Pillow-roller for bed, which is also designed for sleep, and for decorative decoration;
- Sofa decorative rollers under the back;
- Decorative rollers can be used as an armrest and even as a footrest.
- Decorative pillows rollers photo
- Bed Pillow
- Sofa pillows rollers are good for several reasons: First, they are comfortable to put them under the head, under the back, on hand, under the feet, secondly, they fit well into any interior, can become a bright accent in the room And perfectly combined with square on one.
- Sofa pillows rollers photo
In the form of decorative Pillow-roller It may be straight, with accuracy repetitive shape of the cylinder, and maybe with a granted edge, in this case the assembly crosses either a beautiful button, or "tail" from the fabric, or a decorative brush, as in the case of a roller, made in. By the way, the roller pillows came to us from the east, so made from the "eastern" fabrics, for example, from multi-colored taffeta and decorated with brushes, such people look just great and are an unchanged attribute of eastern interiors.
- Decorative cushion-roller photo
Now, perhaps, we turn to the description of the benefits of rollers. What they are so good that they are not inferior to traditional rectangular pillows, and sometimes even exceed them?
Advantages of roller pillows
To begin with, recall the structure of the human body and the fact that a normal rest is a person gets only when his spine is relaxed. What is needed for this? Very little: so that during sleep and neck, and the head was lying on the pillow.
Only when the back is fixed at one point and the defamations are removed, the spine allows themselves to relax.
Consequently, the back relaxes, the neck, the nervous voltage goes and even removes the pain in the back and the spine.
Those who suffer in back pains need to radically reconsider their attitude to sleep, look at what pillows you sleep, whether they are comfortable, are not beautiful or, on the contrary, are they not low?
Pillow-roller for sleep has a number of therapeutic effects. Much depends on the right position of the body during sleep. For example, both already mentioned above, headaches and pain in the spine are leaving, the work of the heart and blood circulation improves, the pressure is normalized, the eyes relax and the intraocular pressure is reduced.
- Also, the pillow-roller is shown for sleep those who restlessly sleep at night and suffers from chronic fatigue.
By the way, such cushions belong to the category of orthopedic, especially if they are not packed with traditional down and feather, but, for example, hypoallergenic and environmentally friendly buckwheat husk, which, besides, has a massage effect.
And the orthopedic pillows rollers for sleep and recreation are filled with therapeutic herbs to supplement the therapeutic effect of aromatherapy. From the most common aromatic fillers, you can mark juniper, lavender, cedar.
Such rollers not only contribute to strong sleep, but also relieve stress, relax the nervous system, get rid of insomnia.
Features of the manufacture of decorative pillows of rollers do it yourself
For needlewomen, it will be interesting that the pillow-roller is quite easy to produce at home. Moreover, it is so easily sewn that even a beginner seammy can join the manufacture of roller. It looks beautifully roller in style when the decorative pillowcase is made of multicolored flaps of the fabric.
Also on the pillow-roller will be appropriate hand embroidery and lace. On decorative pillowcases, as a rule, a fastener of unborn lightning is made - this is done for the convenience of using the roller, so that if necessary, the pillowcase can be easily removed and wrapped.
And you can fill such a pillow with a traditional octoch and pen or synthetic materials, for example, a foam or holofiber.
Read also ..
A source: https://2balla.ru/how-to-properly-sew-a-cushion-of-foam-rubber-pillowrollers-decorative-and-medicinal-properties.html.
Orthopedic pillow-roller: Features of a healthy sleep (63 photos)
The pillow in the shape of a roller provides complete relaxation of the shoulder muscles during sleep. This is due to a uniform distribution of body weight. The orthopedic pillow-roller when lining it under the head helps to improve blood circulation in hand and neck, reduce headaches, normalizes sleep.
Such a subject is very good to use people whose work is connected with a seating lifestyle. It is also good to put a roller under the neck or lower back for a convenient position of the body. Under swelling or spasms, it is desirable that the pillow-roller pillow for the bed is kneeling, which prevents varicose veins.
Insomnia, pain in the neck and head may well arise from the wrong selected pillow. Magnificent pillows have a negative impact on the state of the upper spine, therefore a long solid cushion should come to the classic cushion. Only she will not allow the deflection of the thoracic spine, speaking support for the neck.
The decorative cushion-roller is used in any room at home, in the place where there is a sofa. Product configurations can have a wide variety of: straight cylindrical, "bone", "Horseshoe" and many other types.
Pillows rollers for the sofa are used not only for lining under the top spine, lower back or head. The product can be used as coasters under elbows or legs. The scope of decorative pillows-rollers depends on the fantasy of their owner. The sofa pillow-roller must certainly be combined in color with a colors of the sofa.
Manufacturers turned the pillow-roller to the present healing agent. Pillow-roller for sleep can have many different fillers. The most common filler is buckwheat husk, inexpensive and environmentally friendly material.
In addition, a pillow-roller for sleep can be filled with polyurethane foam, latex and a variety of other materials. Increasingly, you can find items with the effect of memory that can adapt to the contours of the body and provide additional support for the back.
Women are happy to use rollers for neck with a cooling effect, which, according to manufacturers, prolong youth.
Since the orthopedic pillow-roller is designed to relax on the side, the height of the roller must correspond to the distance from the beginning of the neck until the end of the shoulder. Other factors affect the comfortable position of the body during sleep:
- cushion filler cushion;
- hardness and other characteristics of the mattress;
- body weight;
- Favorite positions in a dream.
It is best when choosing to lie on the pillow-roller, as the elasticity and the volume of the product for each person are individual. If a complete relaxation of the neck and shoulders came in the lying position, then the pillow fits perfectly.
It should be borne in mind that the pillow-roller cushion should not be used under the weight of a person.
As a result of a competently selected rolling pillow, a person wakes up with a pleasant feeling of lightness in the whole body and with a good mood.
Application Pillow-roller for children
Using a pillow in the form of a roller for children is of great importance. She makes it possible to sleep on the side and plays the role of support for the weak muscles of the kid. Merry baby pillows are produced in the form of various animals: cats, dogs, tigering. They are nice to the touch and have colorful bright colors.
Pillow-roller does not require much care. Removable case must be erased from time to time manually or on a washing machine. Sew the pillow in the form of a roller is recommended in a ventilated room, away from hot batteries and avoiding the sun. Do not resort to chemical cleaning so that chemicals do not impregnate the product filler and did not cause allergies.
How to make a pillow-roller yourself, on the Internet you can see many master classes with step-by-step instructions. Pillow-roller pillow is pretty easy. We reject details, sew pillowcase, pinch the filler, add buttons and laces. The production process requires:
- roller from the foam rubber;
- batting and thin material of rare weaving for tosing a foam rubber;
- cloth for pillowcase;
- Threads suitable for color;
- two big buttons or tassels;
- lace for Kant;
- sewing machine.
All necessary accessories can be purchased in specialized stores that sell fabrics and various fittings.
Special attention should be paid to the choice of fabric from which the pillowcase is sewn. Usually, velor, tapestry, satin and other materials are used for this purpose. Color is selected to your taste with the interior of the room. The sides of the roller pillow are decorated with details that can be combined in color or, on the contrary, be contrasting.
There are several ways to sew a pillow-roller. The most common is the manufacture of three parts: the main element in the form of a rectangle and two side parts. So that the pillowcase perfectly tightened the pillow, it is necessary to take measurements very carefully.
In addition to solid foam rubber, a pillow-roller can be made of soft batting. For this, the material is collapsed with a roll to the desired diameter and turns close marks or another material with rare weaving.
An interesting version of pillowcases for pillow rolling is a pillowcase "sweetie". A large web fabric of the rectangular form turns into a foam shape, on the sides, tapes with ribbons and the pillow becomes like a big candy.
It is not bad to produce a decorative pillow-roller for any purpose along with children. The fantasy of children is limitless, and they will definitely bring unusual ideas in the design of such a piece of items.
Pillows rollers are produced for those who care about their health and health of loved ones, especially children.
Original Multifunctional Sleep Pillows will help to cope with the problems of the upper spine, upper and lower extremities, eliminate headaches, normalize sleep and prevent some diseases. They do not require special care and advantageously complement the interior of the room, being an original decoration.
If you have any questions - leave them in the comments under the article. We or our visitors will gladly respond to them
A source: https://roplan.ru/dekorirovanie/podushka-valik/
Arrangement of the house
Making a pillow-roller with their own hands
Instructions for the manufacture of a simple pillow-roller and roll under the neck do it yourself
There are two versions of roller pillows - Simple and pillows rollers for the neck. And the one, and the other can make an independently novice needlewoman. To work, you will need a polyester attachment, a cloth for a cover, braid, cord or tape. Depending on the stylistics of the room, such a sofa decor can be performed in the color of upholstered furniture or, on the contrary, create a bright contrast spot.
Buy the finished form or make it yourself. If you want, you can for a pillow-roller made with your own hands, sew a muslin case, following the instructions for creating a regular roller cushion, but not to insert zippers and sew the opening.
An elegant pillow-roller can be decorated with additional decorative details: braid, cord, rolling. Put it on the edge of the studio couch, which in the afternoon turns into sofa.
Below are the master classes for the manufacture of a simple roller pillow and roll for the neck.
How to make a simple cushion-roller with your own hands: master class
To make a shape for a pillow-roller according to the size you need, just roll a sheet of polyester attack in the roller of the desired size. Sew the ends of the attack so that the roller does not roll.
Before you sew a pillow-roller with your own hands, you need to make a pattern. For this:
- Measure the width of the shape from the edge to the edge, and then add 2.5 cm input to the seams. Measure the length of the shape, and then add a 5 cm of the allowance on the seams. Use two of these measurements when the cover pattern.
- Measure the diameter on one side of the shape and add 2.5 cm allowance for the seams. Use this measurement to carve round sections from paper. Cut two round sections.
- Insert the zipper into the long seam cover using the exhibition in the center. Open zipper.
- If you want, on the seam line at the ends of the case, you can make a different finish: cord, ruffles or something else.
- Scaliate the case and one final (round section) with the right side to each other, so that untreated edges coincided. Working with the final (round section), step it up with 12-mm seam. Repeat the procedure with another round section.
- Remove the cover on the right side and insert the cushion into it.
How to make a pillow-roller with your own hands, is shown on these photos:
Making a roller pillow under the neck with your own hands
Pillow-roller under the neck is ideal for relaxing on the bed while reading. It is a less formal version of a simple roller pillow with a beautiful assembly and tape, which is tightened with the opening at one end.
In order to sew a cushion-roller under the neck with your own hands, act as follows:
- Measure and cut the long section of the cover just as for a simple roller pillow.
- Measure the diameter of one end (round part) of the form. Divide on 2, then add 4 cm insertion on the seams and the trim. Use this size and measuring the length plus 2.5 cm to carve out two rectangles for the final (round) sections.
- Skolit one end section with the right side inside so that short edges coincided. Stop 12-mm seam by finishing a line of 5 cm from one long end. Stick the seams uncovered.
- At the open end of the seam, wrap the unprocessed edge under the bottom of 6 mm and lay. Wrap it up for 2 cm for 2 cm and label. Close each fold with a firmware stitch.
- Repeat the procedure on another terminal section
- Scaliate the cover with the right side inside so that long edges coincide, and save 12-mm seam. Stick the seams uncovered. Remove the cover on the right side.
- If you want, notify the cord, flip or other inserted trim along the seam line at the ends of the cover.
- Scaliate the case and one final section with the right side to each other so that untreated edges and seams coincide. Stop 12-mm seam. Repeat the procedure on another end section.
- Insert a tape or lace into the trim, insert the cushion and pull the laces and make a bows.
See how beautiful cushions made with your own hands for the neck on these photos:
Even on the topic do not miss